✔ Solder-less Instal
✔ Solder-less Pickup Changes
✔ Coil Splitting (Auto Converts Humbuckers to Single Coils)
✔ Options for 50s' or 60's control layouts
✔ Improved Clarity & Control
Super Easy, Solder-less Install
All ObsidianWire Pro-Wired Electronics are super easy to install, and allow for solder-less pickup changes with ObsidianWire Plug, Play & Enjoy connectors.
Humbuckers to Singlecoils and Back Again
Coil Tap Wiring for Les Paul®
Split your humbuckers into single coils for classic, low output spank, and back again with a tap of the volume control.
A pop in replacement for your Gibson® Les Paul® wiring harness.
The ObsidianWire Custom SC is a Split Coil / Coil Tap upgrade wiring harness for your Les Paul®. The upgrade uses premium CTS push / Pull pots for ultimate tonal flexibility, and saves you a whole lot of work by making the install super easy and 100% solder-less.
(requires 4 conductor pickups)
ObsidianWire SC Switching
Split your humbucker pickups into single coils, allowing for Strat® or Tele® like tones, and back again with a push or pull of the volume control.
Each pickup has its own switch, so you can split each one on its own, or both at the same time.
Both Switches Down (Traditional LP)
Position 1: Bridge Humbucker
Both Switches UpPosition 1: Bridge Single Coil
Position 2: Bridge Single Coil + Neck Single Coil
Position3: Neck Single Coil
Neck Volume Switch Up - Bridge Volume Switch DownPosition 1: Bridge Humbucker
Position 2: Bridge Humbucker + Neck Single Coil
Position3: Neck Single Coil
Neck Volume Switch Down + Bridge Volume Switch UpPosition 1: Bridge Single Coil
Position 2: Bridge Single Coil + Neck Humbucker
Position3: Neck Humbucker
Built Around the ObsidianWire 60s Circuit
Cut Through at Any Volume
The ObsidianWire 60s wiring retains treble when you roll back the volume control allowing you to retain your overall tone and cut through at lower volumes. The controls are more intuitive with the 60s set, with the tone control changing tone and the volume control changing the volume.
We have a small team of people that love crafting Pro-Wired Electronics and we take pride in producing the absolutes best. We use custom specified parts, perfected techniques, and hand test to ensure that your harness will be an upgrade for your guitar, from factory model to custom shop.
World’s Best Craftsmanship and Components
- ObsidianWire Custom Select 500k Pots (Crafted by CTS) (+/-8%) US Spec Split Shaft / 24 Spline
- Premium Selected CTS Split Shaft Push / Pull Pots 500k (+/-10%)
- Obsidian Select Pro-Wired Toggle Switch
- Obsidian Select Capacitors (150 Series Polyester Film 0.022uf) (+/-5%)
- Genuine Switchcraft J11 Mono Output jack
- Pre Printed & Easy to Follow Wiring Diagram
- Endless Customer Support
- Fits Gibson & Epiphone Les Paul® ONLY – See Notes Below
- American Series Gibson® Les Paul® – Direct Fit // Right Hand Guitars Only
- Epiphone® Les Paul® – You will need to widen the control holes out to 10mm and get new US Spec, 24 spline knobs to fit the higher grade electronics. // Right Hand Guitars Only
- - Note that Some Epiphone hole spacings vary from standard spec and will not fit. Check Hole Spacing against diagram HERE
- Non Official Les Pauls / Les Paul Copies - DOES NOT FIT
- SG - DOES NOT FIT
- PRS - DOES NOT FIT
- Tele Deluxe - DOES NOT FIT
- Left Hand Guitars - DOES NOT FIT
- Three Pickup Les Pauls - DOES NOT FIT